We're building in public. New features land every week. Tell us what you'd like to see added.

LEARN MODULAR

Start here

Short lessons in plain words. Each one links to the patches, modules and case planner on Modular Atlas, so you can try it as you go.

WANT A FULL COURSE?

Learning Modular

A full course site for modular synthesis, from first patch to advanced techniques. A great next step after the lessons below.

Visit Learning Modular ↗
01

What modular is

A modular synth is a synth taken apart into separate boxes, called modules. You connect them yourself with patch cables, so you decide how the sound is built.

Three kinds of signal travel through the cables:

  • Audio: the sound you hear.
  • Control voltage (CV): a slow-moving voltage that turns knobs for you, like pitch or filter brightness.
  • Gates and triggers: on/off pulses that say "play a note now".

In Eurorack all three use the same small 3.5 mm cables, which is why almost anything can be patched into anything.

02

Your first sound

The smallest playable voice needs three modules:

  • An oscillator (VCO) makes the raw tone.
  • A VCA opens and closes the volume.
  • An envelope tells the VCA how fast to open and how long to ring.

Patch the oscillator into the VCA, the envelope into the VCA's CV input, and send a gate to the envelope. Each gate now plays a note.

See the patch in the Patch Library · Find modules for it

03

Filters shape the tone

A filter removes part of the sound. A low-pass filter keeps the lows and cuts the highs, so turning it down makes the sound darker and rounder. Resonance boosts the frequencies right at the cutoff point for that classic squelch.

Patch an envelope into the filter's cutoff input and every note gets brighter at the start and mellows as it fades.

Find a filter that fits your case

04

Modulation: making it move

Modulation means using one signal to keep turning another module's knob.

  • LFOs are slow oscillators for wobble, sweeps and vibrato.
  • Envelopes make a shape every time a note plays.
  • Random and sample & hold give movement that never repeats.
  • Attenuverters turn modulation down, or flip it upside down, so it's never too much.

Find LFOs and attenuverters

05

Clocks and sequencers

A clock is a steady pulse that keeps everything in time. A sequencer steps through a pattern of notes or voltages with each pulse. Clock dividers make slower pulses from one clock, so parts can play at half or quarter speed.

Random notes sound musical when they go through a quantizer, which snaps them to a scale.

Find sequencers and quantizers

06

Volts per octave

Pitch in modular follows a simple rule: 1 volt up = 1 octave up. That's why a sequencer, a keyboard interface and a quantizer can all play the same oscillator in tune.

Audio signals are much bigger, about 10 volts from peak to peak, so expect them to be loud when you patch audio into a CV input.

07

Space and power

Eurorack modules are measured in HP. One HP is 5.08 mm, and a common case row is 84 or 104 HP wide. Check two more things before you buy:

  • Depth: some modules are too deep for slim cases.
  • Power: add up each module's +12V and −12V draw in milliamps and keep the total under about 80% of what your power supply gives.

The case planner does all this math for you as you add modules.

Open the case planner

08

Your first case

Start smaller than you think. A good first rack has one or two sound sources, a filter, two VCAs, a couple of envelopes, an LFO, some attenuators and a mult, plus a way in (MIDI or a sequencer) and a way out to headphones or your mixer.

Buying used is a great way to start, and you can always sell a module that doesn't click with you.

Plan a case · Browse used gear

09

East coast and west coast

East coast style starts with a bright tone and carves it with a filter, the classic sound of the early big modulars. West coast style starts simple and adds harmonics with wavefolders and complex oscillators, then shapes the volume and tone together with low-pass gates.

Most racks today mix both. Try a low-pass gate on a plucky sequence and hear the difference.

Find low-pass gates and wavefolders

10

Install modules safely

  • Turn the case power off before adding or removing a module.
  • Line up the red stripe on the power ribbon with −12V on the module and on the bus board. A ribbon in backwards is the most common way modules get damaged.
  • Don't overtighten the screws; snug is enough.
  • Turn the power on and check for smoke, heat or strange smells before you patch.

Want to build your own module? Start with the 11-step DIY guide. The Prototype Lab is coming soon.